12/11/2023 0 Comments Andis clipper cleaner solutionPlace three drops of the oil along the top of the blade teeth at the top left, right, and center of the blade. ![]() Oil themįinally, you can apply the clipper oil – again with the blade teeth pointed downwards. Let it sit for a couple of minutes, and then carefully wipe the excess away with a clean, soft, and dry cloth. Take care to hold the unplugged clipper with the blade angled downwards and spray the solution directly onto the blades. You can then spray the clippers with a specially designed disinfecting spray to remove any residual bacteria. The handle you can then wipe down with a damp cloth. While it’s fine to air dry your clippers, it’s better to pat them dry so that you know all moisture has been removed and there’s no chance of them rusting while stored away. Again unplug them or remove the power source so that you can safely dry the blades. Turn off the clippers and remove them from the solution. You will then need to run the clippers for a few seconds so that the solution gets to every part of the blades. Take care not to put so much of the clippers into the solution that there is a danger any of it will seep into the electrical areas. Next, pour the cleaning solution into the container and submerge the blades while they are in the clippers. ![]() If you have a clipper with detachable blades, remove them and get right down into the nooks and crannies of the clipper to remove as much as you can this way. Starting with the blade brush, wipe away any hair clippings that are caught up in the teeth of the blades or down in the blade drive. So make sure that your clippers are (initially) unplugged or that their power source has been removed. A Step-By-Step Guide to Cleaning Your Dog Clippers Using the wrong products could invalidate your warranty. Check the instructions provided by the manufacturer to see if they have any specific recommendations. Some types of cleaners aren’t suitable and could cause damage. Take care which chemicals you are using on your blades. These are often multifunctional, helping with cleaning, keeping the blades cool, and more.Ī word of caution. Plus, a small container to put it in.ĭisinfecting spray to eliminate any bacteria. Things you can use to clean your clipper and blades.Ī cleaning solution that is specifically designed for cleaning blades. If one hasn’t been supplied for you, an old toothbrush, pipe cleaner, interdental brush – basically anything with bristles – will usually do the trick. If not, don’t worry you’ll easily be able to pick up something suitable online.Ī clipper brush for brushing out hair and dust. Often manufacturers supply the basics with the clippers themselves. Luckily, you don’t need much to keep your clippers in pristine condition. Tools You Will Need for Cleaning Your Dog Clippers You will then need to oil the blades to keep them clean and well-lubricated, which will ensure they remain free from rust and function well the next time you need them. This takes just a little bit of the hassle out of what can, unfortunately, often be a tricky, tedious task.Īs well as removing any hair and dirt from the blades and the cutting mechanism, you are also going to need to disinfect your clippers (as you should with all your grooming tools) to prevent bacteria from growing here. ![]() That way, they will be ready for you the next time you need them. As you will be clipping your pup every 7-10 weeks for best results, we recommend cleaning them each time you use them. This could damage the clippers or, even worse, give you or your pet a nasty shock.Īs outlined above, your clippers are going to need regular maintenance. Keep the blade section angled down to ensure that no moisture enters the main electrical parts of the clippers. In this case, you will need to spray the front of the blade, not the cutting edge, allow it to work its magic for a minute or two, and then wipe away the excess fluid.Īside from being careful of the blades themselves when cleaning your clippers, it’s a good idea to unplug corded clippers and remove the battery of cordless ones to avoid them accidentally switching on as you are dismantling the clippers to remove hair cuttings from inside the mechanism.īe sure to wash the clippers with a cleaning fluid specifically designed for this purpose. You might need to turn the clippers off for a bit, switch out the blade, or use a cooling spray. Inspect the cord for any signs of damage, the blades for noticeable rusting, and the blade holders so you can be sure they are secure.ĭuring use, pay attention to how hot the blades are becoming, especially during intensive grooming. Before using the clippers, there are a few general maintenance checks you should carry out to ensure they are in good condition.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |